• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive way to increase the security of your home. This process isn't for everyone. It requires a certain amount of patience and expertise.

You must replace window Lock the cylinder, which is within the knob's body. The cylinder is responsible for recognizing the key as it is inserted in the lock.

Take off the lock that was previously used.

The first step in replacing the door lock is to remove the lock that was previously in use. It is a fairly simple process, but it is important to keep some things in your mind. Make sure that the new lock fits the door. This will ensure it is secure and doesn't leave a gap at the deadbolt or latch.

After you have removed the latch plate, you will need to look for two bolts or screws in the casing's interior that are holding the casing to the double glazed window lock repair halves. Unscrew them using a screwdriver, then take the lock out of the door. If you have a mortise lock there could be a set screw located at the base of the handle that holds it to the spindle. Use a screwdriver to remove this screw, then remove the doorknobs.

You must also remove the latch and deadbolt plug from the hole in the door jamb. Install the new lock. If you're replacing a mortise, you must take a measurement of the distance between the lock case and your door's edge to make sure that the new lock is a good fit.

You might want to change your lock for a variety of reasons, such as when you suspect that someone else is holding the key or if you have new roommates. In any event, you can save money by taking the upvc window lock repairs off yourself, rather than hiring an expert to remove it. It's much easier than you think and can be completed in a matter of a few minutes.

Remove the trim and handle of your door. With a flat screwdriver pry off the trim. You should be able twist off the majority of it. In some instances you may be able remove the handles completely. Next, examine the handle for a small pinhole on the inside and insert a straightened paper clip into it. This will activate the release mechanism, which allows you to take off the handle. Next, examine the inside of the lock to find a small tab, and then press it using a screwdriver that is flat. After the spindle has been removed, you can remove the housing and the cylinder.

Selecting a new lock

When it comes to selecting a new lock there are a lot of choices. Take a look at the various types of repair window locks and choose one that matches the style of your door. Think about the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole that runs along the edge of the door frame). Select a lock that will fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded the majority of locks for doors to give you an idea of their longevity and how difficult it is to pick them up or disable them. A grade 3 lock may be the ideal choice for a tranquil apartment building in the country, while locks of grade 1 might be better suited to an area with a lot of traffic, such as an open-air storefront.

Most smart door locks require a digital key code to open. If you're concerned about security breaches or hacking you should consult an expert locksmith or your local police department for assistance.

Replacing the cylinder

If the cylinder of your door lock is broken or damaged it can be replaced within a matter of minutes with a simple do-it-yourself project. It is important to select the correct cylinder and follow all instructions. The first step is to remove the handle or knob should there be one then loosen the trim around the base of the lock cylinder with the aid of a screwdriver. Once the trim is removed, you can access the screws that hold the cylinder in place and remove them with the flat-head screwdriver. The cylinder is then gently removed away from the door.

Make sure you measure the length of your new cylinder prior to putting it in place. Take a measurement of the distance from the center to the right and left sides of the cylinder using an instrument. Then, you can purchase an additional cylinder using the same measurements. This will stop cylinders from snapping when the door is hit or the key is stuck inside.

If you have a replacement cylinder, insert it into the door and turn the key. This will align the cylinder with the carriage which is typically on the outside of your lock. Then, loosen the set screws that should be a couple of turns in the head. If there is a screw located on the outside of the case that is holding the door, you'll have to loosen it.

After you have removed the lock cylinder and replacing it with the new lock by slipping the new cylinder into the case and tightening the set screw. You should also reinstall the bracket that connects the cylinder with the stem for the lock indicator, which you can do by pulling out three small tabs on the back of the cylinder using needle-nose pliers. Then, you can attach the second bracket to the back of the cylinder. You should then reinstall the strike plate and latch plate, as well as the retaining rings that are connected to the top of the lock the cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. The majority of residential locksets are designed for doors with a thickness of 1 3/8 to 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This would include longer screws and either an extension for the spindle or a longer the tail piece for door knobs.

The majority of locks come with a detailed installation guide to aid you. Read the instructions carefully before beginning the process to make sure that you are following all the steps. The manual will also provide you with an idea of the level of skill required to complete the task. You may want to ask a person who has experience changing locks for help if you are changing locks for the first time.

It's a great idea to tape the openings in the old lock before installing the new lock. This will stop screws from falling through the holes and will also protect any tiles you may have installed. It will also prevent any possible damage caused by rust, dirt, and grime. SECURAM Touch includes the masking strip or gaffer tape, however you can use any tape you have.

After taking off the screws that connect the lock's inner half to its exterior then remove the lock immediately. It's crucial to do this swiftly so that the lock doesn't end up closing itself in a way that could end up harming the mechanism.

If the new lock comes with an internal latch bolt, insert the new latch bolt into the upper cross bore. Be sure to put it in the correct position, which is usually marked by an illustration on the faceplate. Then, slide the latch plate onto the bolt and screw it in place.

Finally, screw in the deadbolt and strike plates to the door jamb. Test the deadbolt a few times, throwing it around to see if it extends into the strike plate. Follow the instructions that come with your electronic smart lock to program it. This requires downloading an application, registering your e-mail address, verifying you identity, and connecting to the wireless network to add your device.